CODELOCKS 4OOO ELECTRONIC Uživatelský manuál stáhnout pdf (Strana 4)

PROGRAMMING

ENTER NEW USER CODE Program 01

Key Sequence

#Master Code

•

User Code ID (eg 05)

•

New Code (eg 4321)

••

Result

New code 4321 entered at User Code ID 05

(

•

when user enters code)

SUSPEND USER CODE Program 02

Key Sequence

#Master Code

•

User Code ID (eg 05)

••

Result

User Code at ID 05 suspended

(

••

when user 05 enters code)

RESTORE USER CODE Program 03

Key Sequence

#Master Code

•

User Code ID (eg 05)

••

Result

User Code at ID 05 restored

(

•

when user 05 enters code)

SUSPEND ALL USER CODES Program 04

Key Sequence

#Master Code

•

••

Result

All User Codes suspended

(

••

when all users enter code)

RESTORE ALL USER CODES Program 05

Key Sequence

#Master Code

•

••

Result

All User Codes restored

(

•

when all users enter code)

CHANGE UNLOCK TIME Program 06

Key Sequence

#Master Code

•

enter open time

(range 2 – 9 secs)

••

Result

After code entry the lock will unlock for the set time

(Factory pre-set time is 4 seconds)

ONE TIME USER CODE Program 07

Key Sequence

#Master Code

•

One time code ID

(eg 81)

•

One time Code (eg 4321)

••

Result

Code 4321 in position 81 will work once and then

be removed from memory

Note: ID Positions 81 to 90 are reserved for this

program function, allowing up to 10 One-Time

User Codes to be entered.

SET CODE FREE MODE Program 08

Key Sequence

#Master Code

•

••

Result

Lock will be continuously unlocked

CANCEL CODE FREE MODE Program 09

Key Sequence

#Master Code

•

••

Result

Lock will revert to normal operation

CHANGE MASTER CODE

Program 10

Key Sequence

#Master Code

•

enter length of Master Code

followed by new Master Code (eg 6, 123456)

•

confirm length of Master Code followed by new

Master Code (eg 6, 123456)

••

Result

Master Code now changed to #123456. Note: If the

length of the Master Code is changed then all

previous User Codes will be deleted

CANCEL EMERGENCY OPEN MODE

Program 11

Key Sequence

#Master Code

•

••

Result

The emergency unlocked condition via REM 2 will

be cancelled and the lock will revert to normal

operation

DELETE ALL USER CODES Program 12

Key Sequence

#Master Code

•

••

(7 secs)

Result

All User Codes will be cleared from the memory

First change the factory Master Code #1234 – see program 10. If the Master or Sub Master

Code is entered 3 times consecutively without performing a programming function, a penalty

time of 10 seconds is activated.

Note: On the CL2000 and CL4000 locks the at the bottom of the keypad acts as the # button.

The Master Code and Sub-Master Code MUST always start with #. Codes can only be the same length

as the Master Code. A

•

in the Key Sequence below indicates LED illumination.

IF ENTERED, A SUB-MASTER CODE CAN BE USED INSTEAD OF THE MASTER CODE FOR ALL PROGRAMS

EXCEPT PROGRAMS 10 AND 12.

•

Code accepted

•

Code rejected

••

Code(s) valid

but suspended

LOCKED/UNLOCKED STATUS Program 15

Key Sequence

1. #Master Code

•

••

=Locked, No LED

flashing (this is the default setting)

2. #Master Code

•

••

=Locked-Red

•

LED flashing

3. #Master Code

•

••

=Unlocked-Blue

•

LED flashing

Result

If activated LED’s will flash continuously every

5 seconds

Note: LED’s will not indicate unlocked mode by key

ADD/CHANGE SUB-MASTER CODE Program 13

Key Sequence

#Master Code

•

Sub-Master Code (eg

2468)

••

Result

A Sub-Master Code #2468 has been entered

DELETE SUB-MASTER CODE Program 14

Key Sequence

#Master Code

•

••

Result

Sub-Master Code has been deleted

6 7

1 2 3 4

Komentáře k této Příručce

Žádné komentáře

CODELOCKS 4OOO ELECTRONIC Uživatelský manuál Strana 4

Komentáře k této Příručce